Chastity gear with a length of less than four inches

Hello all, I’m on the smaller end of the size spectrum. Right now I use a Birdlocked Mini, but its total length is around 4 inches, which matches my erect measurement perfectly. Ideally, I want to stop growth at just over 2.5 inches (that’s roughly how long I am when soft). Could anyone point me toward male chastity devices that have an overall length under 3 inches? I’ve looked at a few options but held back because I wasn’t sure about the measurements. The smaller versions of the Holy Trainer, Dickcage, and the “Stainless steel Male Boundage chastity More Short Cage Gimp GAY SM Fetish A080” from DHGate have caught my eye (even though some folks doubt that brand). … 63084.html I’m ruling out the CB6000s because of those dreaded seam-splitting stories, but I’d appreciate it if you could share dimensions for other compact devices. Specifically, I need to know the total length when fully put together, ring included. Any advice is welcome, though precise sizing feels essential before buying anything new. Cheers!

You could try a CB6K. When I started using CD models two years ago, I didn't realize you shouldn't give the little guy any room to expand at all, so I purchased a Curve... and it split (quite painful; luckily super glue fixed it. Next up was an MM JB, half an inch shorter, which is lovely but still too long. So before returning that JB for shortening, I bought the 6Ks cage as a test fit (it works with the Curve rings). I took care to avoid splitting, especially since the plastic felt much thinner than the Curve's. After building up to a full week of non-stop wear without any splits! Perhaps they've finally solved that issue. Anyway, trying the 6Ks gave me enough confidence to have my JB shortened properly.

I doubt you'll find an "off-the-shelf" unit that fits your specs. Most are mass-produced for the average user. For your specific needs, a custom device is likely your best bet.

> member_75c78a1ec7 wrote:I doubt you'll find an "off-the-shelf" unit that fits your specs. Most are mass-produced for the average user. For your specific needs, a custom device is likely your best bet. Seconded. They might be pricey, but it sounds like you know exactly what you need and want. You're perfect for a custom piece. I can't say enough good things about Mature Metal's craftsmanship and customer service. To them, this isn't just business; it's something they truly care about.

That was my suspicion too, but I held out hope for a Christmas miracle:) Now it's just a tug-of-war between saving money and enduring discomfort to see if or when I'll pay for a custom one.

Mature Metal as well as Steelwerks here in Canada produce EXCELLENT custom devices for "little guys.":-D

I’ve had the holy trainer small on and off for a month or so. Previously, I experimented with the cb3k - it was too large; the cb6ks were close but overly wide; and birdlocked - I should have waited until they released the mini version. The HTs fits perfectly. The ergonomic rings have been quite comfortable from day one, though their sizing details can be somewhat unclear. I’m wearing the smallest ring (40mm), yet with the 6ks I was a size no5, and in the 3k I was a size no3!! These sizes indicate the internal height of the rings; the widths are greater because they aren't perfectly round.

It sounds like the Short Story is exactly what you’re looking for. ... stity-cage I know it comes with a higher price tag, but think of it as a long-term investment. Actually, I just went ahead and got a 4 gauge piercing to make this chastity lifestyle feel more secure and real for me. Save up, get the best quality, and you won’t have any regrets, my friend. You’ll be able to use that good device for the rest of your life. In contrast, a bad one or an ill-fitting model might not even grant you a single day of comfort.

I own an A080. In fact, I’m sitting here wearing it right now. It is made of stainless steel. I ordered and received a 50mm ring. I slipped a small piece of vinyl tubing over the post to ensure that the cage sits snugly against the rear stop when the lock is inserted. It may not be fully custom-made, but it is reasonably crafted, has no rough edges, and the price was just right.

I wore a cb6ks for about six months (and I’m wearing it again now while my MM devices are temporarily unavailable). It’s an excellent device and can be kept clean even with extended wear.

I'm in the same situation. I've been able to test quite a few belts and cages. To me, it's important that a cage maintains contact with the glans at all times. This matters less for stopping erection length from growing than for keeping urination neat. Most quality cages—whether metal, plastic, or silicone—feature a front opening large enough for normal peeing without spraying if the head rests against the device end. I found several budget-friendly options (under $75) on Amazon in short sizes. I picked up one with a 2-inch cage and another with a 2½-inch cage. The 2½-inch version usually leaves about half an inch of space beyond the tip. Since flaccid length fluctuates, sometimes it fit well and other times there was noticeable gap. The 2-inch model fits snugly; getting into it took some effort at first, looking like I might overflow. Still, it felt good with my head pressed firmly against the cage end. Clearly, there's no room for length expansion, though girth does increase when arousal approaches. Both models come with removable urethral tubes which are comfortable and short enough to avoid infection risk. It seems smart to grab a few of these short devices to trial them. Once you identify your preferred size, upgrading to an MM cage or other premium option becomes simple since you know exactly what measurements to order. I have photos on my site (not promoting it heavily, but they might help). You can check me in two sample models here: ... ttings.htm and see how poorly a Bon 4 suits me on this page: ... astity.htm. None of the cages I've tried until recently came close to fitting me as well as these two new devices. One question: On the MM site, there are sizing queries about cage diameter. The budget models I bought for testing have a 1½" diameter. That size fits me fine, but I'm unsure if it's the correct specification for a custom device. Any advice? Thanks

You should ask them directly about your question. They are very knowledgeable and familiar with other devices available. Best of luck